company logo Gymnastics 4 Hire

How To: Make a Scooter Board

Jul 2015

First Published: Sunday 12-Jul-2015 9:56 PM, Edited: Sunday 12-Jul-2015 9:56 PM
Author: Gary Black

Share this article

submit to reddit Share on Tumblr Subscribe to RSS

scooter board

Total cost - a bit of time and about $15 per scooter board.

See previous article Super Scooters for some fun scooter board ideas, more to come.

Disclaimer: The measurements in this article are what I have found to be a good balance between portability, functionality, and safety. Your experiences may differ.

You Will Need

plywood Plywood (1200 mm x 595mm at Bunnings ‘Formply’ - $9.95) – Comes in a large sheet, you can cut out multiple boards.

wheelswheels Wheels – They need to swivel, you want the ones with ball bearings and a plate that you can screw to the bottom of the board. Get small ones, if they are too big the board will sit too high off the ground and become unstable, or fingers could get caught in them. Don’t touch the ones that screw through the board – these come unscrewed and fall off. The ones in the picture are from Bunnings, $ 1.98 each, but they no longer stock them. They have magic white ones now that cost just over $4 and do the same thing.

screws Screws – This is to attach the wheels to the board.

pencil Pencil – To mark where to cut.

try-square Try / Set Square – for nice straight lines at 90deg.

circular-saw Power saw – You can use a hand saw, but it’s much easier with a powered saw.

sander Sandpaper / Electric Sander – Again, you can do it by hand but if you have a powered sander it’s much easier.

paint Paint / Varnish – Whichever takes your fancy, if your painting then use an oil based enamel, I’ve found it to be more durable.


1. Start with the plywood, use a pencil to mark in 250 mm from the left, at both the top and bottom of the board. Use a ruler or straight length of timber or metal as an edge to help draw a straight line on the timber connecting the two marks.


2. Using a saw, cut the board along the line. If you have a drop saw big enough you can use this to get a nice straight cut. I don’t have one. To get a long straight cut with a circular saw (pictured), I use a long piece of timber or metal.

straight cut

Line up the blade of the saw with the pencil line on the timber. Mark on the timber where the edge of the metal plate of the saw sits (it’s normally about 35mm from the blade). Measure how far from the cutting line this mark is. Mark the same distance at the other side of the board. Clamp your nice long bit of straight wood to the board on this new line. Saw the board with the plate of the saw hard up against the clamped on timber. This will give you a nice straight cut.

3. On the smaller piece you just cut off, measure and mark a line 354 mm from the bottom. Do as above to cut along this line.


You should now have a small rectangle of plywood measuring 250 mm by 354 mm. This is the top of your scooter board.

Why 250 mm by 354 mm? It is stable enough, and fits nicely into the metal box I use to transport all my trinkits. It also allows the boards to be stacked in a way the is very compact (upside down they fit inside each other at 90 deg angles. The 354 mm came from Pythagoras constant, and is also the same ratio used for A4 paper.

4. Grab out the sander and sand all the edges, so that it is nice and smooth. Don’t forget to blunt the edges and corners of the board as well.

5. On the underneath of the board (whichever side you choose to make the bottom), use a try / set square to measure and mark a line 15 mm from the edge of the board. Do the same on all 4 edges.

15mm line

6. Position the wheel so that the edge of the bottom plate of the wheel is on the 15mm line you just drew. So the fastening plate of the wheel is 15mm from the corner. Any closer to the edge and the board will not be strong enough to hold the screw closest to the corner of the board.

attach wheel attach wheel

7. Use either a power drill or hand screw driver to screw in 4 screws to attach the wheel to the board.

8. Repeat steps 6 and 7 for all 4 corners.

9. Paint or varnish to your liking.

scooter board

Total cost - a bit of time and about $15 per scooter board.

Facebook Like Have you liked us on Facebook?

If you or your kids like what we do, then please take a few seconds to show your support and like our Facebook page.

Back to the index

Share this article

submit to reddit Share on Tumblr Subscribe to RSS

-- Comments --

Be the first to comment on this...

Add a Comment with your Gymnastics4Hire login

--OR Comment with Facebook--

Blog Directory & Business Pages -

About Gary Black...

Gary Black

Advanced Silver Mens Gymnastics Coach, Intermediate Womens Gymnastics Coach, Intermediate Kindergym Coach.

Gary began running gymnastics programs in schools in 2003. Initially as a casual staff member with another company, whilst studing teaching at Deakin University; and quickly becoming one of their managers. Gary went on to own what was the sole Victorian franchise of that company.

Whilst with that company, under Gary's leadership, Victorian customers enjoyed quality, reliability, flexibility, and understanding.

In mid 2014, to be able to better service the changing needs of schools, Gary decided to move away from a restrictive franchised business, and started Gymnastics 4 Hire, determined to keep the high standards that customers had come to enjoy, and to provide a service specifically tailored to the customers needs.